Classe Audio SSP-300 Uživatelský manuál stáhnout pdf

PRO-INF_FORM-1010 Rev. 01 PRO-INF_CAN BUS USER GUIDE (preliminary dealer release)_V1.6.doc Page 1 of 6

Date:

January 25, 2007

Model Number:

CAN BUS

Classé Audio Inc.

Subject:

CAN BUS USER GUIDE – preliminary dealer release

Classé’s Controller Area Network, or CAN Bus, opens the way to a new level of interaction between

our Delta range of amplifiers, preamps, processors and source components. When connected via CAN

Bus, the different elements of a Delta series system are in constant communication, creating a

“global” network that delivers system wide status information and shared operational features, all

through the touchscreen display.

CAN Bus will allow a single Delta series touchscreen to:

• Display status information for every connected unit, including amplifiers which do not have a

touchscreen display

• Create a “PlayLink” that allows an SSP or Preamp to automatically switch to the correct input

when a Delta series source component starts playback

• Adjust the global system brightness

• Configure the entire system to go in and out of standby at the touch of a button and also bring

individual components in and out of standby

• Mute any connected unit.

CAN BUS SET UP

HARDWARE

Classé Delta Series Products

Two or more Classé Delta series products are required, at least one of which must have a touchscreen

display.

Category 5 Network cables

These are ordinary network cables, commonly used for broadband Internet connections. They should

be typical “straight through” cables not the “crossed over” type, and the total required will be one less

than the total number of Delta series components in your system.

CAN Bus Terminator

These are either included with the products or available free of charge from your nearest Classé

Customer Support Centre

http://www.Classeaudio.com/support/service.htm

A single CAN Bus Terminator is required. It is inserted into the CAN Bus OUT connector of the last

component in the CAN Bus daisy chain.

SSP 300 & 600 CAN Bus Interface Box

Systems that include an SSP-600 or SSP-300 will also require an SSP 300/600 CAN Bus Interface Box.

These are included with the products or available free of charge from your nearest Classé Customer

Support Centre

http://www.Classeaudio.com/support/service.htm .

Classé Audio, Inc. 5070 François Cusson Lachine, Québec Canada H8T1B3

Contact info Tel. : (514) 636-6384, Fax : (514) 636-1428, Email :

cservice@classeaudio.com

1 2 3 4 5 6

Classé Audio Inc 1

Shrnutí obsahu

Strany 1 - Classé Audio Inc

PRO-INF_FORM-1010 Rev. 01 PRO-INF_CAN BUS USER GUIDE (preliminary dealer release)_V1.6.doc Page 1 of

Strany 2

PRO-INF_FORM-1010 Rev. 01 PRO-INF_CAN BUS USER GUIDE (preliminary dealer release)_V1.6.doc Page 2 of

Strany 3

PRO-INF_FORM-1010 Rev. 01 PRO-INF_CAN BUS USER GUIDE (preliminary dealer release)_V1.6.doc Page 3 of

Strany 4

PRO-INF_FORM-1010 Rev. 01 PRO-INF_CAN BUS USER GUIDE (preliminary dealer release)_V1.6.doc Page 4 of

Strany 5

PRO-INF_FORM-1010 Rev. 01 PRO-INF_CAN BUS USER GUIDE (preliminary dealer release)_V1.6.doc Page 5 of

Strany 6

PRO-INF_FORM-1010 Rev. 01 PRO-INF_CAN BUS USER GUIDE (preliminary dealer release)_V1.6.doc Page 6 of

Komentáře k této Příručce

Žádné komentáře

Classe Audio SSP-300 Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro ne Classe Audio SSP-300. Incoming Inspection Specification: Uživatelská příručka

Shrnutí obsahu

Komentáře k této Příručce

Související produkty a manuály pro ne Classe Audio SSP-300